• Home
  • Hard Water
  • Chlorine
  • Periodic Service
  • Cleaning Instructions
  • Installation Guides
  • Owner's Manuals
    • Intermountain Water Products
  • Troubleshooting

Manual Cleaning Instructions

Tuesday, 06 September 2011 16:01 Last Updated on Tuesday, 06 September 2011 16:01 Written by Robert 0 Comments

      

Erie 541-D9/D8/180/360/Water Master pre 2010

To begin a manual cleaning on this water system, gently turn the skipper or 12 day timer wheel counter clock-wise until it stops. Hearing a clicking sound as you turn is normal. Next, turn the small white camshaft wheel clock-wise until it stops. The system should begin cleaning within 15 minutes and the cleaning will last about an hour and a half. If the system does not begin cleaning, call technical support. Don’t forget to set the Time of Day after the cleaning is finished.

5 Button – Imperial/High Country/Spectrum 180/Spectrum 360

 To begin a manual cleaning on this water system, press and release button 1 once. An arrow in the lower left corner of the display will appear indicating the system will start cleaning in 60 seconds. A full cleaning will usually last about an hour and a half. If the system does not begin cleaning after 90 seconds, call technical support.

 

 

 

 

 

SSP/SSD/IMP/HP/WF/EMP/XR2/DX2/Patriot

To begin a manual cleaning on this water system, press and release the left water fountain, star or recycle button multiple times until the display says “Clean in 10 Seconds” or “Regen. in 10 Seconds”. The system will begin cleaning within 10 seconds and will last approximately 2 – 5 hours depending on your system model. If the system does not begin cleaning, call technical support.

 

5600SE/Atlantis DX

To begin a manual cleaning on this water system, press and hold the recycle button for 5 seconds. After 5 seconds the system will begin cleaning. The cleaning will last approximately an hour and a half to 5 hours depending on your specific model. If the system does not begin cleaning, call technical support.

5000SE

To begin a manual cleaning on this water system, press and hold the recycle button for 5 seconds. After 5 seconds the system will begin cleaning. The cleaning will last approximately an hour and a half to 5 hours depending on your specific model. If the system does not begin cleaning, call technical support.

 

 

 

Twinflo100

To begin a manual cleaning on this two-tank water system, press and release the recycle button. The system will begin a cleaning immediately on the tank in service. The cleaning will last approximately an hour and a half. Once the cleaning is finished, press and release the recycle button again to clean the standby tank. If the system does not begin cleaning, call technical support.

 

 

SXT/SXTi Control Platform

To begin a manual cleaning on this water system, press and hold the recycle button for 5 seconds. After 5 seconds the system will begin cleaning. The cleaning will last approximately 2 – 5 hours depending on your specific model.  If the system does not begin cleaning, call technical support.

 

XTR/XTRi Control Platform

To begin a manual cleaning on this water system, press and hold the recycle button for 5 seconds. After 5 seconds the system will begin cleaning. The cleaning will last approximately 2 – 5 hours depending on your specific model. If the system does not begin cleaning, call technical support.

 

Sensory Twin/Patriot Analyst/All 9100 and 9100Tsi Control Platforms

To begin a manual cleaning on this water system, press and hold the recycle button for 3 seconds. A solid cleaning icon will be displayed and the control will immediately begin cleaning on the tank in service. After 5 seconds, press and hold the recycle button again.  A solid x2 icon next to the cleaning icon will appear indicating a manual cleaning on the standby tank will begin immediately after the current cleaning cycle is complete. The dual-tank cleaning will last approximately 4-6 hours depending on your specific model. If the system does not begin cleaning, call technical support.

 

6700/Atlantis XR/Original Water Fountain

To begin a manual cleaning on this water system, press and hold the recycle or guest button for 5 seconds. After 5 seconds the system will begin cleaning. The cleaning will last approximately an hour and a half to 5 hours depending on your specific model. If the system does not begin cleaning, call technical support.

Patriot/Water Fountain Winged

To begin a manual cleaning on this water system, press and hold the “star” or “guest” button for 5 seconds. After 5 seconds the system will begin cleaning. The cleaning will last approximately 3 – 5 hours depending on your specific model. If the system does not begin cleaning, call technical support.

5600 Econominder

To begin a manual cleaning on this water system, turn the black knob from the ‘service’ position to the ‘backwash’ or ‘brine rinse’ position – whichever comes first. The system will begin cleaning immediately. If the system does not begin cleaning, call technical support.

Copyright (c)2000 Intermountain Soft Water